Patz Model 1512 Manure Pump

• Plunger Size: 7 x 15 in.
• Stroke Lengths: 20 in., 17 in. and 14 in.
• Hole Size for Pump Installation: 5 ft. wide x 14 ft. long x 7 ft. 3in. deep (approximately).
• Floor Space Required for Pump: 3 ft. 2 in. x 11 ft. (approximately).
• Weight: 2,350 lb. (approximately).
• Safety Railing: Standard equipment.
• Pipe Length: Recommended maximum length of pipe with no elbows, 150 ft. Deduct 5 ft. for each 22-1/2° elbow used and 10 ft. for each 45° elbow. Up to 90° of elbows may be used in one installation.
• Pipe Size: Choose 15" or 12" PVC pipe.
• Storage Height (Head): Maximum storage height (head) is 25 ft.
• This is measured from center line of pipe at manure pump to top of manure in storage area.

Patz Model 3333 Multi-Use Vertical Pump

• Tapered-bore drive pulley mounts to a 1-1/8-inch (29 mm) drive shaft with a greaseable flange bearing at the top of the drive tube
• Easy access to oil reservoir
• High-volume delivery
• Protection against bearing contamination
• Bearing seals can be purged every 8 hours thanks to a grease line from the seal pack to the top of the pump
• Clogging prevented and positive input provided
• Shear plate has two legs to help support pump off the floor of the pit
• Impeller transition area features beefed-up steel for long life
• Pump available in various lengths to fit pit depths of 3 12 feet

Patz Model 4444 Vertical Pit Pump

• Pumping capacity up to 1,580 gals./min
• Available in lengths to fit your application: 6 ft. (1.8 m), 8 ft. (2.4 m), 10 ft. (3.0 m), and 12 ft. (3.6 m)
• A 16-inch (40.6 cm) Impeller for added capacity
• Variable agitation capacities with a standard dual agitation system
• Abrasion-resistant steel in high wear areas for longer life.
• Tapered-bore drive pulley mounts to a 1-3/4 inch (44.5 mm) drive shaft with a greaseable flange bearing at the top of the drive tube
• Easy access to oil reservoir
• Lifting loops located on top of the pump allows easy insertion and removal of the unit from the pit with a tractor loader, skid-steer loader or winch
• A steel mounting plate is included as standard equipment to allow precise positioning of the pump to match the pit depth. Plate can be lagged to a concrete pad or curb
• Pump available in various lengths to fit pit depths of 5 ft. 6 in. (1.7 m) to 12 ft 10 in. (3.9 m).

6000 & 8000 PTO Drive Vertical Pit Pumps

• Stationary base secured to manure pit or two-point tractor hitch with hydraulics for tilting
• Match your pit depth with choice of four pump lengths: 6, 8, 10 and 12 feet (1.83, 2.44, 3.05 and 3.66 m)
• Large U-bolts allow the frame to be adjusted up or down for precise placement
• Match your desired speed of transfer and loading with two pump sizes: 6-inch (152 mm) and 8-inch (203 mm) pipe
• Reduce agitation time with dual nozzles that blend crusted manure and settled solids into a liquid slurry fast
• Get better pit clean out by agitating every corner with adjustable nozzles (rotate both horizontally and vertically)
• Remove clumps of straw with chopping action over impeller shredder plate
• Lower repair costs with impeller housing of abrasion-resistant steel in high-wear areas
• Tractor Requirement: 100 HP minimum

Model 6000E Electric Drive Vertical Pit Pump

• A stationary base secured to manure pit is standard on the 6000E Pump
• Equipped with a two-point tractor hitch for easy insertion and removal from pit for service
• Match your pit depth with choice of four pump lengths: 6, 8, 10 and 12 feet (1.83, 2.44, 3.05 and 3.66 m)
• Large U-bolts allow the frame to be adjusted up or down for precise placement
• Get better pit clean-out by agitating with a nozzle which can be rotated horizontally
• Save time when agitating, transferring, and loading due to swept-back impeller blades for high-volume pumping up to 2,500 gallons per minute-during agitation and 2200 gallons per minute during loading
• Horsepower Requirements: Twin 15, 20, 25, or 30 HP, 3-phase motors.

Patz Model 9000 Liquid Transfer System

• Pump: 1/2 hp. 1625 RPM: Single phase; 230 volts; 5.8 amps; 84 lb. (38 kg); maximum solids diameter: 2" (50.8 mm); two-vane, non-clogging impellers
• Pump Performance: G.P.M. at total head in feet
• Gutter Widths: 15" to 20"
• Hole Size for Installation: 18" (457 mm) wide x 24" (610 mm) long x 30" (762 mm) depth below gutter bottom (20 gal. sump)
• Pipe Size: 2" (50.8 mm) PVC schedule 40 Pipe supports should be every 10' (3m) apart
• Height to top of handle: 19-3/8"
• Width at widest point: 12-5/8"
• Discharge: 2 NPT
• Suction inlet opening: 2"
• Weight: 84 lb.